TY - JOUR
T1 - Improvement of high-temperature shape-memory effect by multi-component alloying for TIPD alloys
AU - Matsuda, Hiromichi
AU - Sato, Hirotaka
AU - Shimojo, Masayuki
AU - Yamabe-Mitarai, Yoko
N1 - Funding Information:
The study was partly supported by “Precious Metals Research Grant of TANAKA Memorial Foundation”, for which the authors express thanks.
Publisher Copyright:
©2019 The Japan Institute of Metals and Materials
PY - 2019
Y1 - 2019
N2 - The influence of multi-component alloying on the phase transformation and shape-memory effect was investigated to develop new high-temperature shape memory alloys (HT-SMAs). Four alloys®35Ti20Pd15Ni15Pt15Zr, 40Ti20Pd15Ni15Pt10Zr (high-entropy alloys, HEAs), 45Ti20Pd5Ni25Pt5Zr, and 45Ti20Pd10Ni20Pt5Zr (medium-entropy alloys, MEAs, at%)®were prepared. At room temperature, the B2 structure was stable in the HEAs, and no martensitic transformation (MT) was observed. However, in the MEAs, an MT from the B2 structure to a B19 structure was clearly observed. The MT temperature of the MEAs was comparable to or higher than those of binary and ternary TiPd alloys. The strengths of both the martensite and austenite phases in 45Ti20Pd5Ni25Pt5Zr were higher than those in 45Ti20Pd10Ni20Pt5Zr and ternary TiPd alloys. We attempted to explain the high strength using the ¤ parameter, which indicates the lattice distortion for various atomic sizes, but a clear correlation was not observed, as there were no significant differences in the ¤ parameter among the tested alloys. The shape recovery was investigated via a thermal cyclic test under an applied stress in the range of 15200 MPa. Although a small plastic strain was introduced during the thermal cyclic test, a shape recovery over 80% was obtained for both MEAs. Training, that is, the thermal cyclic test under the same applied stress, was conducted to investigate the change of the irrecoverable strain and the work output. For 45Ti20Pd5Ni25Pt5Zr, the irrecoverable strain was deleted after 50 cycles, and perfect recovery was obtained. The largest work output (3.5 J/cm3) was obtained under 200 MPa. In 45Ti20Pd10Ni20Pt5Zr, perfect recovery was obtained from the first cycle. However, the recoverable strain was small, and the largest work output was 1.5 J/cm3 under 200 MPa. The shape recovery of 45Ti20Pd5Ni25Pt5Zr is promising for new HT-SMAs compared with the ternary TiPdZr alloys and other HEA-SMAs.
AB - The influence of multi-component alloying on the phase transformation and shape-memory effect was investigated to develop new high-temperature shape memory alloys (HT-SMAs). Four alloys®35Ti20Pd15Ni15Pt15Zr, 40Ti20Pd15Ni15Pt10Zr (high-entropy alloys, HEAs), 45Ti20Pd5Ni25Pt5Zr, and 45Ti20Pd10Ni20Pt5Zr (medium-entropy alloys, MEAs, at%)®were prepared. At room temperature, the B2 structure was stable in the HEAs, and no martensitic transformation (MT) was observed. However, in the MEAs, an MT from the B2 structure to a B19 structure was clearly observed. The MT temperature of the MEAs was comparable to or higher than those of binary and ternary TiPd alloys. The strengths of both the martensite and austenite phases in 45Ti20Pd5Ni25Pt5Zr were higher than those in 45Ti20Pd10Ni20Pt5Zr and ternary TiPd alloys. We attempted to explain the high strength using the ¤ parameter, which indicates the lattice distortion for various atomic sizes, but a clear correlation was not observed, as there were no significant differences in the ¤ parameter among the tested alloys. The shape recovery was investigated via a thermal cyclic test under an applied stress in the range of 15200 MPa. Although a small plastic strain was introduced during the thermal cyclic test, a shape recovery over 80% was obtained for both MEAs. Training, that is, the thermal cyclic test under the same applied stress, was conducted to investigate the change of the irrecoverable strain and the work output. For 45Ti20Pd5Ni25Pt5Zr, the irrecoverable strain was deleted after 50 cycles, and perfect recovery was obtained. The largest work output (3.5 J/cm3) was obtained under 200 MPa. In 45Ti20Pd10Ni20Pt5Zr, perfect recovery was obtained from the first cycle. However, the recoverable strain was small, and the largest work output was 1.5 J/cm3 under 200 MPa. The shape recovery of 45Ti20Pd5Ni25Pt5Zr is promising for new HT-SMAs compared with the ternary TiPdZr alloys and other HEA-SMAs.
KW - B19
KW - B2
KW - High-temperature shape-memory alloys
KW - Multi-component alloys
KW - Shape recovery
KW - Thermal cyclic test
KW - TiPd
KW - TiPt
UR - http://www.scopus.com/inward/record.url?scp=85074215448&partnerID=8YFLogxK
UR - http://www.scopus.com/inward/citedby.url?scp=85074215448&partnerID=8YFLogxK
U2 - 10.2320/matertrans.MT-MAW2019012
DO - 10.2320/matertrans.MT-MAW2019012
M3 - Article
AN - SCOPUS:85074215448
SN - 1345-9678
VL - 60
SP - 2282
EP - 2291
JO - Materials Transactions
JF - Materials Transactions
IS - 11
ER -